PPC Laser-Printable Films

Raw material sizes:

Master roll (by width)

Finished Goods stock sizes:

Sheets

		8.5x11"	11x17"	12x12"	12"x18"	17"x22"
Clear PPC/Laser
	.004"/100um	•	•	•			Pk/50 Sheets
1/Side Matte
	.003"/75um	•	•		•	•	Pk/100 Sheets
	.004"/100um	•	•		•	•	Pk/100 Sheets
	.005"/125um	•	•		•	•	Pk/100 Sheets
	.007"/175um	•	•		•	•	Pk/100 Sheets
2/Side Matte
	.003"/75um	•	•		•	•	Pk/100 Sheets
	.004"/100um	•	•		•	•	Pk/100 Sheets
	.005"/125um	•	•		•	•	Pk/100 Sheets
	.007"/175um	•	•		•	•	Pk/100 Sheets

Properties are based on .004″/100um Clear PPC/Laser film. Properties of other gauges and finishes of PPC/Laser film can vary.

Film Property				Value	Units	Test Method
	Physical Properties
		Tensile Strength (MD)		28000	psi	ASTM D 882
		Tensile Strength (TD)		34000	psi	ASTM D 882
		Strength Elongation MD		15000	psi	ASTM D 882
		Strength F-5 TD		14000	psi	ASTM D 882
		Modulus MD		710000	psi	ASTM D 882
		Modulus TD		740000	psi	ASTM D 882
		Elongation MD		115	%	ASTM D 882
		Elongation TD		92	%	ASTM D 882
		Density		1.39	g/cc	ASTM D 1505
		Viscosity		0.56	dL/g	ASTM D 4603
	Electrical Properties
		Dielectric Strength
			AC, 20°C, .00092"	7000	volts/mil	ASTM D 149-64
		Dielectric Constant
			25°C, 1 kHz	3.2		ASTM D150-81
		Dissipation Factor
			25°C, 1 kHz	0.005		ASTM D150-65
		Volume Resistivity 25°C		1.0E+19	ohm-cm	ASTM D257-78
		Corona Threshold		425	V-AC	ASTM D2275-80
	Thermal Properties
		Melt Point		200	°C
		Service Temperature Range		-70-150	C
		Dimensional Stability
			at 105° MD	0.6	%	Measured Shrinkage
			at 105° TD	0.9	%	Measured Shrinkage
			at 150° MD	1.8	%	Measured Shrinkage
			at 150° TD	1.1	%	Measured Shrinkage
		Specific Heat		0.28	cal/g/°C
		Thermal Expansion		1.7x10-5	in./in./°C	ASTM D 696
	Optical Properties
		Transmission Visible		> 80	%
		Transmission Near IR		>80	%
		Haze		<3	%
		Refractive Index		1.65	RI
	Chemical Properties
		Permiability
			Water Vapor	0.1	g/100 in2/24hr.	ASTM E-96
			Carbon Dioxide	16	g/100 in2/24hr.	ASTM D1434-58
		Mosture Absorbtion		<.8	%	ASTM D-570-63

Important Notice:  Grafix makes no warranties, express or implied, including but not limited to any implied warranty of merchantability of fitness for a particular purpose.  The user is responsible for determining whether the Grafix product is fit for a particular purpose and suitable for the user’s method of application.  Please remember that many factors can affect the use and performance of a Grafix Plastics film product in a particular application.  Given the variety of factors that can affect the use and performance of a Grafix product, some of which are uniquely within the user’s knowledge and control, it is essential that the user evaluate the Grafix product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.

Limitation of Remedies and Liability:  If the Grafix product is proven to be defective, THE EXCLUSIVE REMEDY, AT GRAFIX’S OPTION, SHALL BE TO REFUND THE PURCHASE PRICE OF OR TO REPAIR OR REPLACE THE DEFECTIVE GRAFIX PRODUCT. Grafix shall not otherwise be liable for loss or damages, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including, but not limited to, contract, negligence, warranty or strict liability.